86 lines
3.4 KiB
Markdown
86 lines
3.4 KiB
Markdown
## TESO-O Fun Robot at Hackaday Supercon 2023
|
|
|
|
Firmware for TEST-O: The Continuity and Diode Test Funbot
|
|
|
|
This is a PlatformIO-compatible project.
|
|
|
|
|
|
|
|
**BE AWARE:**
|
|
On REV1 boards, the right potentiometer only works for the first half of its rotation. Turning the right pot beyond half way _will not cause damage_, but the addon will consume extra current (up to ~3-5mA). If the knob is within the affected second half of rotation, the eye LEDs will flash red as an indicator while in RGB fun mode.
|
|
|
|
To work around this, use the right pot only within the first half of its rotation.
|
|
|
|
|
|
|
|
|
|
## What can you do with it?
|
|
|
|
The TEST-O Robot is:
|
|
|
|
- A continuity meter
|
|
- Set the switch to the left position.
|
|
- Use the provided probes to check continuity.
|
|
- The left eye will show continuity status.
|
|
- Continuity is indicated if a resistance of ~100ohms or less is detected.
|
|
- Turn the buzzer on or off using the button while in this mode.
|
|
- Testing voltage is ~1.2V and limited to ~2mA.
|
|
|
|
- A diode test meter
|
|
- Set the switch to the right position.
|
|
- Use the provided probes on the diode.
|
|
- The right eye will show diode test status.
|
|
- Status is updated if the diode conducts (positive on anode, negative on cathode).
|
|
- Shorts are shown with a different eye LED color.
|
|
- LEDs can be tested, though not all will light or indicate on the right eye.
|
|
- Testing voltage is ~3.1V and limited to ~2mA.
|
|
|
|
- An RGB light show with long dangly probe arms
|
|
- Up to you if you want to short things out with dangly probes
|
|
- 7 configurable RGB programs available
|
|
- Turn the potentiometers to set program parameters
|
|
- There is an empty RGB LED program slot available for hackers to add one
|
|
|
|
|
|
## Hacking
|
|
|
|
Use a DAPLink probe to debug. If you don't have one, there are many projects to convert existing devboards to DAPLink.
|
|
|
|
If you want to hack on this without a debug probe, an XMODEM bootloader is available. Use a TTL UART to connect to the UART pins on the addon header. To activate the bootloader, ensure the left knob is between halfway to full clockwise. Press and hold the button while powering on. The bootloader will now indicate it is working with flashing LEDs, and will communicate at 115200-8-N-1. Send your firmware.bin file using XMODEM using a terminal emulator.
|
|
|
|
|
|
## Specifications
|
|
|
|
- PUYA PY32F003W16S6 MCU
|
|
- ARM Cortex-M0+ core running at 8MHz
|
|
- 32K Flash / 4K RAM
|
|
- 2x RGBLED for indicators or fun mode
|
|
- Low-power piezo buzzer for continuity test
|
|
- Built-in continuity cheeks and LED test antenna
|
|
- Pots to set things just how you want them
|
|
- Works as an addon, or standalone with a CR2032
|
|
|
|
|
|
## Misc Notes:
|
|
|
|
- This device is using PUYA PY32F003 MCU, an MCU intended for
|
|
the China domestic market. This MCU, as well as other
|
|
PY32F002A/003/030 cores with at least 32K flash, internally
|
|
uses the same core (and has the same features) as PY32F030F6P6.
|
|
|
|
- The normal firwmare does not use UART and leaves the pins configured
|
|
as SWD for the user.
|
|
|
|
- There is no official OpenOCD support for this MCU. This project uses
|
|
pyOCD as adding PUYA MCU to pyOCD is trivial. Using OpenOCD, J-Link,
|
|
or anything other than the DAPLink compatible debugger with pyOCD
|
|
is untested and left as an exercise to the programmer.
|
|
|
|
|
|
## Credits
|
|
|
|
Original idea by rCON. Idea tweaked and implemented by true.
|
|
|
|
Art modified by rCON and further modified by true.
|
|
|
|
Schematic, board layout, code, and assembly by true. |