dc32-peppercon9-addon/firmware/user/main.c

/*
 * Peppercon9
 * GAT Addon Firmware
 * by true
 *
 * code was made for different random addons I designed for dc32,
 * then adapted to each one. so things might be a mess.
 *
 * I had only a few hours on and off over a week to get the code done.
 * lots of shit was copied from demo code and adapted to work. certainly
 * isn't the best way to get this done.
 *
 * I know I could save some power, but seeing as all the badges burn it in
 * LEDs and almost nobody else power optimizes their badge code, who cares?
 *
 * sorry. wasn't procrastination I swear. all the ideas were last minute.
 *
 * notes:
 *
 * - last 2K of flash memory is reserved for configuration storage.
 */

#include <ch32v20x.h>
#include <stdint.h>

#include "src/adc.h"
#include "src/btn.h"
#include "src/config.h"
#include "src/i2c.h"
#include "src/led.h"
#include "src/lis2dw.h"
#include "src/rand.h"
#include "src/touch.h"
#include "src/ui.h"


void systick_init(void)
{
    SysTick->CMP = (SystemCoreClock / 512) - 1;     // we want a 512Hz interrupt
    SysTick->CNT = 0;                               // clear counter
    SysTick->CTLR = 0xF;                            // start counter in /1 mode, enable interrupts, auto-reset counter
    SysTick->SR = 0;                                // clear count comparison flag

    NVIC_EnableIRQ(SysTicK_IRQn);                   // enable interrupt
}

void gpio_init()
{
    GPIO_InitTypeDef gpio = {0};

    gpio.GPIO_Speed = GPIO_Speed_2MHz;

    // unused osc pins
    gpio.GPIO_Mode = GPIO_Mode_IPD;
    gpio.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_7;
    GPIO_Init(GPIOD, &gpio);

    // unused PORTA pins (0=none, 1=none, 5=SWI2C_SCL, 9=none)
    gpio.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1 | GPIO_Pin_5 | GPIO_Pin_9;
    GPIO_Init(GPIOA, &gpio);

    // unused PORTB pins (5=SWI2C_SDA)
    gpio.GPIO_Pin = GPIO_Pin_5;
    GPIO_Init(GPIOB, &gpio);

    // lightsense LED anode and cathode (2=anode, 3=cathode)
    gpio.GPIO_Mode = GPIO_Mode_Out_PP;
    gpio.GPIO_Pin = GPIO_Pin_2 | GPIO_Pin_3;
    GPIO_Init(GPIOA, &gpio);

    // TBTN1 front touch button, right side (A4)
    gpio.GPIO_Mode = GPIO_Mode_AIN;
    gpio.GPIO_Pin = GPIO_Pin_4;
    GPIO_Init(GPIOA, &gpio);

    // TBTN2 front touch button, left side (A9)
    gpio.GPIO_Pin = GPIO_Pin_1;
    GPIO_Init(GPIOB, &gpio);

    // rear RGBLED (6=T3C1 blue, 7=T3C2 green)
    gpio.GPIO_Mode = GPIO_Mode_AF_PP;
    gpio.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;
    GPIO_Init(GPIOA, &gpio);

    // rear RGBLED (1=T3C3 red)
    gpio.GPIO_Pin = GPIO_Pin_0;
    GPIO_Init(GPIOB, &gpio);

    // accelerometer interrupt
    gpio.GPIO_Mode = GPIO_Mode_IN_FLOATING;
    gpio.GPIO_Pin = GPIO_Pin_15;
    GPIO_Init(GPIOA, &gpio);

    // I2C SCL, SCA for on-board devices
    gpio.GPIO_Mode = GPIO_Mode_AF_OD;
    gpio.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;
    GPIO_Init(GPIOB, &gpio);
}

int main(void)
{
    // configure core
    NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);
    SystemCoreClockUpdate();

    // enable peripheral clocks
    RCC_APB1PeriphClockCmd( RCC_APB1Periph_TIM3  | RCC_APB1Periph_I2C1  |
                            RCC_APB1Periph_PWR, ENABLE);
    RCC_APB2PeriphClockCmd( RCC_APB2Periph_AFIO  | RCC_APB2Periph_GPIOA |
                            RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOD |
                            RCC_APB2Periph_ADC1  | RCC_APB2Periph_ADC2, ENABLE);

    // configure gpio pins
    gpio_init();

    // get saved settings
    i2c_init();
    userconf_load();

    // configure hardware
    adc_init();         // configure ADC1 for lightsense, also configures ADC clock divider
    btn_init();         // configures ADC2 touch buttons on the front
    lis2dw_init();      // looking at badge: Y+ up, X+ right, Z+ in front of badge
    led_init();         // configure matrix IC as well as RGB PWM

    // configure random
    tinymt32_init(&tinymt32_s, DBGMCU_GetCHIPID() | userconf.checksum);

    // configure UI
    ui_init();

    // configure systick interrupt
    systick_init();

    rgb[0] = 10;
    rgb[1] = 10;
    rgb[2] = 10;

    // do system shit
    while(1) {
        __WFI();

        // after sending LEDs, run our program
        // to update the LED buffer for next time
        if ((ticnt & 0x3) == 0) {
            ui_render();
        }
    }
}