OrcaSlicer-bambulab/resources/profiles/Flashforge/filament/Flashforge Generic ASA.json

{
    "type": "filament",
    "name": "Flashforge Generic ASA",
    "inherits": "fdm_filament_asa",
    "from": "system",
    "setting_id": "GFSA04",
    "filament_id": "GFL99",
    "instantiation": "true",
    "additional_cooling_fan_speed": [
        "0"
    ],
    "bed_temperature_difference": [
        "10"
    ],
    "chamber_temperature": "0",
    "close_fan_the_first_x_layers": [
        "2"
    ],
    "compatible_printers": [
        "Flashforge Adventurer 5M 0.4 Nozzle",
        "Flashforge Adventurer 5M 0.6 Nozzle",
        "Flashforge Adventurer 5M 0.8 Nozzle",
        "Flashforge Adventurer 5M Pro 0.4 Nozzle",
        "Flashforge Adventurer 5M Pro 0.6 Nozzle",
        "Flashforge Adventurer 5M Pro 0.8 Nozzle",
        "Flashforge AD5X 0.4 nozzle",
        "Flashforge AD5X 0.6 nozzle",
        "Flashforge AD5X 0.8 nozzle"
    ],
    "compatible_printers_condition": "",
    "compatible_prints": [],
    "compatible_prints_condition": "",
    "cool_plate_temp": [
        "60"
    ],
    "cool_plate_temp_initial_layer": [
        "60"
    ],
    "default_filament_colour": [
        ""
    ],
    "enable_overhang_bridge_fan": [
        "1"
    ],
    "enable_pressure_advance": [
        "1"
    ],
    "eng_plate_temp": [
        "60"
    ],
    "eng_plate_temp_initial_layer": [
        "60"
    ],
    "fan_cooling_layer_time": [
        "30"
    ],
    "fan_max_speed": [
        "20"
    ],
    "fan_min_speed": [
        "10"
    ],
    "filament_cost": [
        "20"
    ],
    "filament_density": [
        "1.04"
    ],
    "filament_deretraction_speed": [
        "nil"
    ],
    "filament_diameter": [
        "1.75"
    ],
    "filament_flow_ratio": [
        "0.98"
    ],
    "filament_is_support": [
        "0"
    ],
    "filament_max_volumetric_speed": [
        "18"
    ],
    "filament_minimal_purge_on_wipe_tower": [
        "15"
    ],
    "filament_retract_before_wipe": [
        "nil"
    ],
    "filament_retract_restart_extra": [
        "nil"
    ],
    "filament_retract_when_changing_layer": [
        "nil"
    ],
    "filament_retraction_length": [
        "nil"
    ],
    "filament_retraction_minimum_travel": [
        "nil"
    ],
    "filament_retraction_speed": [
        "nil"
    ],
    "filament_settings_id": [
        "Flashforge  ASA"
    ],
    "filament_shrink": [
        "100%"
    ],
    "filament_soluble": [
        "0"
    ],
    "filament_start_gcode": [
        "; filament start gcode \n;right_extruder_material:ASA"
    ],
    "filament_end_gcode": [
        "; filament end gcode\n"
    ],
    "filament_type": [
        "ASA"
    ],
    "filament_vendor": [
        "Generic"
    ],
    "filament_wipe": [
        "nil"
    ],
    "filament_wipe_distance": [
        "nil"
    ],
    "filament_z_hop": [
        "nil"
    ],
    "filament_z_hop_types": [
        "nil"
    ],
    "full_fan_speed_layer": [
        "0"
    ],
    "hot_plate_temp": [
        "105"
    ],
    "hot_plate_temp_initial_layer": [
        "105"
    ],
    "nozzle_temperature": [
        "260"
    ],
    "nozzle_temperature_initial_layer": [
        "260"
    ],
    "nozzle_temperature_range_high": [
        "270"
    ],
    "nozzle_temperature_range_low": [
        "230"
    ],
    "overhang_fan_speed": [
        "80"
    ],
    "overhang_fan_threshold": [
        "25%"
    ],
    "pressure_advance": [
        "0.04"
    ],
    "reduce_fan_stop_start_freq": [
        "1"
    ],
    "required_nozzle_HRC": [
        "0"
    ],
    "slow_down_for_layer_cooling": [
        "1"
    ],
    "slow_down_layer_time": [
        "5"
    ],
    "slow_down_min_speed": [
        "20"
    ],
    "support_material_interface_fan_speed": [
        "80"
    ],
    "temperature_vitrification": [
        "100"
    ],
    "textured_plate_temp": [
        "60"
    ],
    "textured_plate_temp_initial_layer": [
        "60"
    ]
}