{
    "type": "machine",
    "name": "MM hqs hj 0.4 nozzle",
    "inherits": "fdm_machine_common",
    "from": "system",
    "setting_id": "GM001",
    "instantiation": "true",
    "printer_model": "MM hqs hj",
    "default_print_profile": "0.10mm Fine @MM hqs hj",
    "nozzle_diameter": [
        "0.4"
    ],
    "printable_area": [
        "0x0",
        "220x0",
        "220x210",
        "0x210"
    ],
    "printable_height": "300",
    "auxiliary_fan": "0",
    "machine_max_acceleration_travel": [
        "3000",
        "3000"
    ],
    "machine_max_acceleration_x": [
        "3000",
        "3000"
    ],
    "machine_max_acceleration_y": [
        "3000",
        "3000"
    ],
    "machine_max_acceleration_z": [
        "500",
        "500"
    ],
    "machine_max_speed_z": [
        "12",
        "12"
    ],
    "max_layer_height": [
        "0.3"
    ],
    "printer_settings_id": "MM",
    "retract_before_wipe": [
        "70%"
    ],
    "wipe_distance": [
        "1"
    ],
    "single_extruder_multi_material": "1",
    "change_filament_gcode": "",
    "scan_first_layer": "0",
    "cooling_tube_length": "20",
    "cooling_tube_retraction": "60",
    "deretraction_speed": [
        "25"
    ],
    "extruder_clearance_height_to_lid": "100",
    "extruder_clearance_height_to_rod": "32",
    "extruder_clearance_radius": "50",
    "machine_max_acceleration_e": [
        "6000"
    ],
    "machine_max_speed_e": [
        "60",
        "120"
    ],
    "machine_max_speed_x": [
        "300",
        "500"
    ],
    "machine_max_speed_y": [
        "300",
        "500"
    ],
    "machine_pause_gcode": "M601",
    "min_layer_height": [
        "0.05"
    ],
    "nozzle_type": "brass",
    "parking_pos_retraction": "22",
    "retract_length_toolchange": [
        "5"
    ],
    "retraction_length": [
        "1.5"
    ],
    "retraction_minimum_travel": [
        "1"
    ],
    "retraction_speed": [
        "25"
    ],
    "machine_max_acceleration_extruding": [
        "2000",
        "1500"
    ],
    "machine_max_acceleration_retracting": [
        "2000",
        "1500"
    ],
    "machine_max_jerk_e": [
        "2.5",
        "2.5"
    ],
    "machine_max_jerk_x": [
        "9",
        "20"
    ],
    "machine_max_jerk_y": [
        "9",
        "20"
    ],
    "machine_max_jerk_z": [
        "0.2",
        "0.4"
    ],
    "z_hop": [
        "0.2"
    ],
    "thumbnails": [
        "220x220"
    ],
    "default_filament_profile": [
        "Generic PLA @System"
    ],
    "z_hop_types": [
        "Slope Lift"
    ],
    "machine_end_gcode": "M104 S0 ;extruder heater off\nM140 S0 ;heated bed heater off (if you have it)\nG91 ;relative positioning\nM83\nG1 E-1 F1200  ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+1 F300 \nG90 ;absolute positioning\nG1 X100 Y0 F6000\nG1 E-4 F1200\nM84 ;steppers off\nM107 ; turn off fan\nPRINT_END",
    "machine_start_gcode": "G0 Z3 F300\nM190 S[bed_temperature_initial_layer_single]\nM109 S[nozzle_temperature_initial_layer]\nPRINT_START EXTRUDER=[nozzle_temperature_initial_layer] BED=[bed_temperature_initial_layer_single]\nG21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 ;Home\n ;G29\nG0 Z5 F300\nG1 X0 Y100 F6000\nG92 E0\nG0 Z0.5 F300\nG1 F1000 Y0 E15\nG1 F1000 X100 E25\nG92 E0 ;zero the extruded length again\nG1 F9000\nM117 Printing..."
}